[ Buon Vino Manufacturing ]

Super Jet Troubleshooting Guide


Most common questions and comments…

Q: Why Should I use "Buon Vino" Filter Pads?
A: You should use Buon Vino Filter Pads because the micron sizes and consistency of Buon Vino Filter Pads have been designed to give optimal performance when used with Buon Vino wine filters. The flow rate of the pump is designed to work in conjunction with the Buon Vino Filter Pads to give you the best filtration possible. For more information, please visit the Filter Pads page.

Q: I have no prime from my pump.
A: This particular pump works on a check-valve system. The check-valve is a functioning part of the pump and will deteriorate due to the acidity from the wine. It is easily replaced. By not allowing solid particulate like oak chips etc. to get into the pump your check-valve will last longer. This part will eventually need changing.

Q: I need a new motor because I am not getting any suction.
A: If your motor is running when you turn it on, you do not need a new motor. You need to replace your check-valve. For check-valve replacement instructions, see below.

Q: My gauge is not registering.
A: Again, due to the acidity in wine the small plate that registers your pressure will deteriorate and you simply need to replace it. Unscrew the gauge to remove it and replace it with the new one. Make sure you put Teflon tape on the threaded portion, to prevent any leaking.

Q: I turn on my motor and it will not run.
A: All our motors have thermal protectors built in. This works in the same manner as a fuse in your house. This part can also be replaced. Please contact the retailer that sold you the filter or Buon Vino Manufacturing directly.

Q: I just put a new set of pads in my filter and my gauge shot up very quickly.
A: Check to see if you have placed your pads and/or filter plates in the filter housing correctly.
Identify the type of wine you are making to the grade of pad you are using. If your gauge rises quickly, this means that your pads are saturating quickly. You may need to filter with a coarser pad. Do not start filtering from the bottom of your container, especially if you have sediment. The pump could draw the sediment into the pads and quickly saturate them. Start filtering about half way down your container. The gauge increases in pressure proportionately to the saturation of the pads. The more saturated your pads get the more back pressure is created, therefore the higher the pressure on your gauge.

Recommendations:

Always flush out your pump well after use and avoid getting solids into your pump. This will make your check-valve last longer.
Clean and dry off the whole machine prior to storage.
Rack your wine prior to filtering.
Lubricate your tightening screw with petroleum jelly or food grade grease. Keep the screw running freely.
Avoid getting liquid on the motor section.



Super Jet Check-valve Replacement


View our Video – Changing your Check Valve or see instructions below:


(for Superjet model #2100 & D48X002B)

1. Unbolt the motor from the frame.
2. Turn the pump head towards you. You will notice 4 screws, take them out.
3. Remove the black pump head.
4. Remove the check-valve.
5. On the check-valve is the seal ring, remove it.
6. Remove the screen to make sure it is clean in behind. It would be a good idea to rinse everything out with water.
Note: It is not necessary to put the screen back in, only if you wish.
7. Insert the new seal ring into the check-valve.
8. Insert the new check-valve into the pump head. At this point the inside should face flush.
9. Place the pump head back on the motor and replace the screws. Make sure you reassemble the hoses to the correct fitting. Then replace the whole unit on the frame as it was before you started.
10. It may on occasion happen that you will not get an immediate prime due to the check-valve and seal ring being dry. Put your inlet tube up the tap and force water through to the pump, this should help prime it.

If your SuperJet is model #2000 series, or if you have any questions about the above instructions, please contact us.

 


Home | About Us | Contact | Bottle Fillers | Wine Filters | Filter Pads
Accessories | Service & Support | Inquiries


Copyright © Buon Vino Manufacturing Incorporated. All rights reserved.
Website hosted by DOC PC Web Creations